Complete Surveillance Solutions
Sales Portal
Share this Product!
STAR-LIGHT PANO™ 6 Megapixel Multi-Sensor Bullet Camera
Model: DWC-PB753WTW

Find a Reseller Request a Demo ContactUs

STAR-LIGHT PANO Cameras use three 2MP CMOS sensors and three 4.3mm fixed lenses to produce stunning 180° views at up to 30fps when placed side by side in a CMS. DW® AHD cameras are engineered to work with VMAX A1™ All-in-One DVRs that record 1080p AHD, TVI and all analog to 960H. AHD provides an easy system upgrade to high definition video.

Important Note: The camera requires a DVR that supports HD over Coax protocols, like the  VMAX A1.
  • DWC-PB753WTW

AHD 6MP 180º Panoramic View Camera
STAR-LIGHT AHD™ Panoramic cameras produce clear 1080p high resolution real-time video images at a 180° viewing angle, increasing the camera's ROI by offering enhanced detail and image clarity for monitoring large areas from a single camera.
  • Analog HD over Coax® technology with HD-Analog signal support
  • Star-Light™ super low light technology
  • 3x 2.1MP/1080p 1/3" image sensor at real-time 30fps
  • 6MP 180° panoramic camera
  • 3x 4.3mm fixed lenses
  • True wide dynamic range (WDR)
  • OSD control via coaxial (UTC)
  • Smart DNR™ 3D digital noise reduction
  • True day/night mechanical IR cut filter
  • De-Fog™ extreme weather image compensation
  • Highlight masking exposure (HME)
  • Auto sensing 24VAC/12VDC with line lock
  • Easy icon driven OSD menu with built-in joystick
  • Programmable Privacy Zones
  • Auto gain control (AGC)
  • Backlight compensation (BLC)
  • Auto white balance (AWB)
  • IP66 environmental-rated dust-tight and water-resistant
  • 5 year warranty


Image sensor
3x 2.1MP 1/3” CMOS
Active pixels
3X 1944 (H) x 1092 (V)
Scanning system
Progressive scan
60Hz / 50Hz
Signal technology
HD over Coax® technology with HD-Analog and all analog to 960H signal support
6 megapixel (3x 1920x1080 Sensors)
Minimum scene illumination
0.06 lux (Color)
0.01 lux (B&W)
S/N ratio
Video output
HD-Analog 6MP (3x 1080p at 30fps + 4ch / 180° panoramic view)
Alarm output
3 alarm outputs


Focal length
Lens type
Fixed lens


x3 (below specs per sensor)
Shutter speed
On, off
Star-Light (sense-up)
Off, x2 – x32
Wide dynamic range (WDR)
True WDR, On, Off
Wide Dynamic Range (WDR) dB 100dB
Digital noise reduction (DNR)
Off, low, middle, high
White balance
Auto / auto-ex / preset / manual
Day / night
Auto, day (color), night (B/W)
Mirror / flip
Auto gain control
Max 60dB
Motion detection
3 zones per camera, total 12 motion zones
Privacy zones
16 privacy zones per camera, total 72 privacy zones
0 ~ 10
RS485 / UTP built-in
Pelco D / A-PC


Operating temperature
-4°F ~ 122°F (-20°C ~ 50°C)
Operating humidity
10–90% RH (non–condensing)
IP rating
IP66 certified weather and tamper resistant
Other certifications


Power requirement
DC12V/AC24V dual voltage
Power consumption
DC12V: 8.5W, 708mA
AC24V: 8.5W, 354mA


Aluminum bullet housing
9.9" x 3.58" (252 x 91 mm)
2.2 lbs (1.0 kg)
Junction box for bullet cameras- White
HD video balun converter
Title Type Size Download
Camera Accessories Compatibility Chart pdf 3.88 MB
DWC-PB753WTW CAD Drawing dwg 0.43 MB
DWC-PB753WTW Data Sheet pdf 0.13 MB
DWC-PB753WTW Manual pdf 26.37 MB
DWC-PB753WTW quick setup guide pdf 0.60 MB
DWC-PB753WTW Sell Sheet pdf 0.17 MB
Frequently asked questions
Q. How to turn on WDR?
A. At the VMAX A1 DVR
  1. Right click and select PTZ controller
  2. Press Menu to access the camera's OSD
  3. Go to Exposure, Brightness and select WDR.
  4. Go to Exit Jump
  5. Select Save & Exit
Q. My camera has a spotlight effect at night.
  1. Enter the Setup Menu
  2. Go to Day & Night
  3. Enable SMART IR and adjust the level
SMART IR adjusts the image for IR cameras to eliminate LED light reflection and white spots in the image. By breaking down the camera’s field of view into five zones, Smart IR allows for even distribution of the IR light. This prevents excessive illumination on images that are in the front of the scene and offers a clear image in B/W without any loss of detail.

Note:  This is best adjusted at night

Q. My Camera image is flashing/flickering
  1. View the image to see if the environment has variable lighting
  2. If so, enable WDR or DRC in the camera’s menu
  3. If not, make sure power is sufficient and power cycle the camera
  4. Check cable and connectors

Wide Dynamic Range (WDR)

Wide Dynamic Range technology mechanically allows capturing an entire scene in challenging lighting conditions. One shutter is set to a short exposure, capturing the bright areas in the FoV, while the other is set for a long exposure, capturing the dark areas in the FoV. The camera then interlaces the images and combines them, capturing both areas with no loss of detail. This allows for an image capture even when there are very bright and dark areas in the camera’s field of view or images are distorted by a strong backlight.

  1. Enter camera's setup menu
  2. Go to Exposure
  3. Go to Backlight and select WDR
  4. Enter WDR submenu to adjust the level
  5. Save & Exit

Dynamic Range Compressor (DRC)

DRC enables dark areas in images to become more visible without overexposing the bright areas to create one perfect image

  1. Enter camera's setup menu
  2. Go to Exposure
  3. Select DRC
  4. Enter DRC submenu to adjust the level
  5. Save & Exit

Q. My camera is blurry at night but clear in the day
  1. Check the lens cover for dirt, debris, scratches, smudges or residue
  2. Tilt camera away from or remove nearby reflective objects
  3. Make sure rubber gasket is present and correctly seated on lens
  4. Clean lens cover with water and dry microfiber cloth
Q. My camera is no longer producing video.
  1. Confirm the physical connection on the dvr
  2. Switch with a known working camera
  3. Check power to the camera
  4. Check camera compatibility
  5. Check user rights
Q. My camera is stuck in Black & Whtie.
  1. Make sure the camera is compatible with the dvr
  2. Make sure the camera is on the right signal
  3. Make sure the camera is getting sufficient light
  4. Make sure the light sensor is not obstructed.
  5. Move camera to a known working port. If problem follows the camera then the camera is the problem
  6. Enter the Camera's setup menu and make sure Day & Night is on Auto
  7. Factory default/Initialize the camera
  8. Bench test the camera with separate wiring and power
  9. Send in for repair if the problem persists.
Q. There are horizontal rolling bars on the monitor.

This is a video ground loop due to more than one ground between camera and monitor/head-end

Ground Loop problems can be resolved by making sure that only one end of any video cable is
connected to a local ground. Make sure the video cable shields do not come into direct contact with
each other to prevent unintentional local grounding.

  1. Tape all connectors in such situations to minimize this risk.
  2. Keep camera runs as short as possible with all video cables cut to fit. Excess cable left along any run can increase the risk of interference.
  3. At the monitor end make sure all the CCTV equipment is connected to same power point to provide a common local ground.
  4. Implement a ground loop isolator

We'd Love to Hear from You

Please submit your information and a DW® representative will get in touch with you

  Call sales at (866) 446-3595


Need help? Don't hesitate to ask us something. Email us directly or call us at (866) 446-3595. You can checkout our F.A.Q. and Help page to get more information about our products.