Complete Surveillance Solutions
Sales Portal
  • DOWNLOAD HIGH-RES PHOTO
Share this Product!
STAR-LIGHT MPA™ 1.3 Megapixel Analog Indoor/Outdoor Ball Camera with IR
Model: DWC-BL2651TIR

Find a Reseller Request a Demo ContactUs

The new STAR-LIGHT™ Megapixel Analog Cameras are a groundbreaking technology with highest analog resolution with a 1.3MP CMOS sensor capable of capturing up to 720P resolution, allowing the camera to receive and process images in high resolution, digitally zoom with no pixelatoin and display up to 820TV Lines resolution. The cameras also offer Intelligent Motion Detection and Automatic Digital Zoom and motion tracing, True Day & Night, 3D Digital Noise Reduction, De-Fog enhancement for extreme weather conditions the Star-Light MPA™ is an intelligent and high resolution solution for any application.

  • DWC-BL2651TIR

DISCONTINUED   

  • 1/3” Sony 1.3MP CMOS, 820TVL [B/W], 800TVL [Color]
  • QuickZoom™ Full Frame 8x Digital Zoom with no Loss in Resolution
  • STAR-LIGHT™ Super Low Light Technology
  • Wide Dynamic Range (WDR)
  • 3.6mm Fixed Lens
  • Smart IR™ with Intelligent Camera Sync. 50ft Range
  • Smart DNR™ 3D Digital Noise Reduction
  • Highlight Masking Exposure (HME)
  • De-Fog™ (Extreme Weather Image Compensation)
  • Secondary Video-BNC Output (While UTP in use)
  • True Day/Night Mechanical IR Cut Filter
  • Programmable Privacy Zones
  • Auto Gain Control (AGC)
  • Back Light Compensation (BLC)
  • Dynamic Range Compressor (DRC) Reveals Low Light Detail
  • Auto White Balance (AWB)
  • IP66 Certified (Weather Resistant)

Image


 
 
Active Pixels (H X V)
 
1280 (H) x 1024 (V)
Frequency
 
15.734KHz (H), 59.95Hz (V)
Image Sensor
 
1/3" Sony 1.3MP CMOS Sensor
Minimum Scene Illumination
 
0.14Lux (F1.2 , 30IRE) at Color 0.03Lux (F1.2 , 30IRE) at TDN(B/W)
Resolution
 
800TVL [Color], 820TVL [B/W]
S/N Ratio- Signal to Noise Ratio
 
55dB (AGC off)
Scanning System
 
2 : 1 Interlace
Synchronization
 
Internal or Line Lock
Video Output
 
CVBS: 1.0Vp-p / 75 ?

Performance*


 
 
Digital Zoom
 
x8

Lens


 
 
Focal Length
 
3.6mm
IR Distance
 
50ft Range IR
Lens Type
 
Fixed Lens

Mechanical


 
 
Dimensions
 
Ø80 X 79.8 mm (3.15 X 3.14 in)
Housing Material
 
Aluminum
Housing Type
 
Ball
Warranty
 
5 Years
Weight
 
0.83lbs

Operational

 
 
AGC
Auto Gain Control
0~20
AWB
Auto White Balance
ATW / AWB / PUSH / MANUAL
BLC
Backlight Compensation
OFF / ON
D/N
Day/ Night
AUTO/ DAY/ NIGHT
DPC- Dead Pixel Cancellation
 
OFF/ ON
DRC
Dynamic Range Compressor
OFF / Low / Middle / High
Gamma
 
0.45 ~ 0.65
HME
Highlight Masking Exposure
OFF / ON
Programmable Privacy Zones
 
OFF / ON (16 Programmable Zones)
Sharpness
 
0~10
Smart DNR™ 3D Digital Noise Reduction
 
OFF / LOW / MIDDLE / HIGH
Starlight™ (Super Low Light Technology)
 
X2-X64
WDR
Wide Dynamic Range
 

Environmental

 
 
Operating Humidity
 
Less than 90% (Non-Condensing)
Operating Temperature
 
-10°C ~ 60°C (14°F ~ 140°F)
Power Consumption
 
LED OFF: 1.6W, 132mA LED ON: 3.36W, 255mA
Voltage
 
12VDC
STAR-LIGHT AHD
STAR-LIGHT PTZ
VMAX A1
Title Type Size Download
Camera Accessories Compatibility Chart pdf 3.88 MB
DWC-BL2651TIR Datasheet pdf 0.25 MB
DWC-BL2651TIR Manual pdf 0.49 MB
DWC-BL2651TIR Presentation pptx 8.93 MB
DWC-BL2651TIR Sell Sheet pdf 0.29 MB
STAR-LIGHT MPA Series Presentation pptx 8.93 MB
Frequently asked questions
Q. My camera has a spotlight effect at night.
A.
  1. Enter the Setup Menu
  2. Go to Day & Night
  3. Enable SMART IR and adjust the level
SMART IR adjusts the image for IR cameras to eliminate LED light reflection and white spots in the image. By breaking down the camera’s field of view into five zones, Smart IR allows for even distribution of the IR light. This prevents excessive illumination on images that are in the front of the scene and offers a clear image in B/W without any loss of detail.

Note:  This is best adjusted at night

Q. My camera is blurry at night but clear in the day
A.
  1. Check the lens cover for dirt, debris, scratches, smudges or residue
  2. Tilt camera away from or remove nearby reflective objects
  3. Make sure rubber gasket is present and correctly seated on lens
  4. Clean lens cover with water and dry microfiber cloth
Q. My camera is no longer producing video.
A.
  1. Confirm the physical connection on the dvr
  2. Switch with a known working camera
  3. Check power to the camera
  4. Check camera compatibility
  5. Check user rights
Q. There are horizontal rolling bars on the monitor.
A.

This is a video ground loop due to more than one ground between camera and monitor/head-end

Ground Loop problems can be resolved by making sure that only one end of any video cable is
connected to a local ground. Make sure the video cable shields do not come into direct contact with
each other to prevent unintentional local grounding.

  1. Tape all connectors in such situations to minimize this risk.
  2. Keep camera runs as short as possible with all video cables cut to fit. Excess cable left along any run can increase the risk of interference.
  3. At the monitor end make sure all the CCTV equipment is connected to same power point to provide a common local ground.
  4. Implement a ground loop isolator

We'd Love to Hear from You

Please submit your information and a DW® representative will get in touch with you

  Call sales at (866) 446-3595

Help

Need help? Don't hesitate to ask us something. Email us directly sales@dwcc.tv or call us at (866) 446-3595. You can checkout our F.A.Q. and Help page to get more information about our products.

Scroll