Contact Sales l Support l or Call us today at (866) 446-3595 Remote Technical Support
Share this Product!
STAR-LIGHT AHD™ 2.1 Megapixel Indoor/Outdoor HD Analog Dome Camera with IR
Model: DWC-V6763WTIR
Groundbreaking STAR-LIGHT AHD™ High Definition Cameras use existing coaxial cables to transmit crystal-clear detailed 1080p images. The cameras offer 2.1MP resolution along with powerful features such as P-Iris Lens, Double Shutter Wide Dynamic Range (WDR) and True Day/Night with Mechanical IR Cut Filter. The STAR-LIGHT AHD cameras are engineered to work with VMAX AHD DVRs, offering an easy upgrade from analog to high definition surveillance using existing infrastructure for a cost-effective, high resolution surveillance solution.
  • DWC-V6763WTIR

Analog High Definition (AHD)
AHD Technology delivers clear HD video
at 1920 x 1080 Resolution.
  • Analog High Definition (AHD) HD over Coax Technology
  • STAR-LIGHT™ Super Low Light Technology
  • Panasonic 1/3" CMOS Sensor
  • 1080p Resolution at 30fps
  • Wide Dynamic Range (WDR)
  • Varifocal P-Iris Lens 2.8~12mm
  • CleanView™ Hydrophobic Dome Coating Repels Water, Dust and Grease
  • Smart IR™ with Intelligent Camera Sync. 100ft Range
  • Smart DNR™ 3D Digital Noise Reduction
  • Highlight Masking Exposure (HME)
  • True Day/Night with Mechanical IR Cut Filter
  • Secondary Video-BNC Output
  • Easy Icon Driven OSD Menu with Built-in Joystick
  • Programmable Privacy Zones
  • Auto Gain Control (AGC)
  • Backlight Compensation (BLC)
  • Dynamic Range Compressor (DRC) Reveals Low Light Detail
  • Auto White Balance (AWB)
  • IP66 Certified (Weather Resistant)
  • 5 Year Warranty


Image Sensor
Panasonic 1/3" CMOS
Active Pixels
1944 (H) x 1092 (V)
Scanning System
Progressive Scan
60Hz / 50Hz
Signal Technology
2.0 Megapixel AHD
1920x1080 (1080p)
Minimum Scene Illumination
F1.4 (30IRE): 0.35Lux [Color]
F1.4 (30IRE): 0 Lux [B&W]

S/N Ratio
Video Output
AHD 1080p30fps / 720p60fps / 720p30fps
Alarm Output
1 Alarm Output


Focal Length
2.8 ~ 12mm
Lens Type
Varifocal P-Iris Lens
IR Distance


Shutter Speed
1/30(25) – 1/30,000
Off / On
STAR-LIGHT (Sense-up)
Off, x2 – x32
Wide Dynamic Range (WDR)
Off / On
Digital Noise Reduction
Off, Low, Middle, High
White Balance
Auto / Auto-Ex / Preset / Manual
Day and Night
Day / Night / Auto
Mirror / Flip
Auto Gain Control
Max 60dB
Motion Detection
Privacy Zones
16 Privacy Zones
0 ~ 10
0.45 ~ 0.75
RS485 / UTP Built-in
Digital Zoom
x1.0 ~ x16.0


Operating Temperature
-20°C ~ 50°C (-4°F ~ 122°F)
Operating Humidity
Less than 90% (Non-Condensing)
IP Rating
IP66 (Weather Resistant)
Other Certifications


Power Requirements
DC12V / AC24V Dual Voltage
Power Consumption
DC12V: 3.1W, 258mA, LED On: 5.41W, 450mA
AC24V: 3.0W, 125mA, LED On: 5.15W, 215mA


144 x 108.8 mm (5.7 x 4.28 inch)
748.4 g (1.65 lbs)
Converter Plate for Electronic Gang Box
Corner Mount Bracket
Outdoor Dome Ceiling Mount Bracket
Outdoor Dome Junction Box
Outdoor Dome Wall Mount Bracket
Pole Mount Bracket
White Converter Plate for Electronic Gang Box
Title Type Size Download
Camera Accessories Compatibility Chart pdf 3.80 MB
DWC-V6763WTIR Datasheet pdf 0.23 MB
DWC-V6763WTIR Datasheet (French) pdf 0.13 MB
DWC-V6763WTIR Datasheet (Portuguese) pdf 0.13 MB
DWC-V6763WTIR Datasheet (Spanish) pdf 0.13 MB
DWC-V6763WTIR Manual pdf 0.82 MB
DWC-V6763WTIR Sell Sheet pdf 0.30 MB
STAR-LIGHT AHD Series Presentation pptx 6.00 MB
Frequently asked questions
Q. How do I get communication from coax?
  1. Camera must be connected to a Vmax A1 dvr or HD-TVI dvr to have coax communication
  2. Camera has 2 video cables make sure to use blue cable for TVI.AHD signal and coax communication
Q. How to turn on WDR?
A. At the VMAX A1 DVR
  1. Right click and select PTZ controller
  2. Press Menu to access the camera's OSD
  3. Go to Exposure, Brightness and select WDR.
  4. Go to Exit Jump
  5. Select Save & Exit
Q. My camera has a spotlight effect at night.
  1. Enter the Setup Menu
  2. Go to Day & Night
  3. Enable SMART IR and adjust the level
SMART IR adjusts the image for IR cameras to eliminate LED light reflection and white spots in the image. By breaking down the camera’s field of view into five zones, Smart IR allows for even distribution of the IR light. This prevents excessive illumination on images that are in the front of the scene and offers a clear image in B/W without any loss of detail.

Note:  This is best adjusted at night

Q. My Camera image is flashing/flickering
  1. View the image to see if the environment has variable lighting
  2. If so, enable WDR or DRC in the camera’s menu
  3. If not, make sure power is sufficient and power cycle the camera
  4. Check cable and connectors
Q. My camera is blurry at night but clear in the day
  1. Check the lens cover for dirt, debris, scratches, smudges or residue
  2. Tilt camera away from or remove nearby reflective objects
  3. Make sure rubber gasket is present and correctly seated on lens
  4. Clean lens cover with water and dry microfiber cloth
Q. My camera is no longer producing video.
  1. Confirm the physical connection on the dvr
  2. Switch with a known working camera
  3. Check power to the camera
  4. Check camera compatibility
  5. Check user rights
Q. My camera is stuck in Black & Whtie.
  1. Make sure the camera is compatible with the dvr
  2. Make sure the camera is on the right signal
  3. Make sure the camera is getting sufficient light
  4. Make sure the light sensor is not obstructed.
  5. Move camera to a known working port. If problem follows the camera then the camera is the problem
  6. Enter the Camera's setup menu and make sure Day & Night is on Auto
  7. Factory default/Initialize the camera
  8. Bench test the camera with separate wiring and power
  9. Send in for repair if the problem persists.
Q. There are horizontal rolling bars on the monitor.

This is a video ground loop due to more than one ground between camera and monitor/head-end

Ground Loop problems can be resolved by making sure that only one end of any video cable is
connected to a local ground. Make sure the video cable shields do not come into direct contact with
each other to prevent unintentional local grounding.

  1. Tape all connectors in such situations to minimize this risk.
  2. Keep camera runs as short as possible with all video cables cut to fit. Excess cable left along any run can increase the risk of interference.
  3. At the monitor end make sure all the CCTV equipment is connected to same power point to provide a common local ground.
  4. Implement a ground loop isolator